[. . . ] Windows 95, Windows 98, Windows NT, and Windows for Pen Computing are trademarks of Microsoft Corporation. All other products are trademarks or registered trademarks of their respective companies. Copyright 1998 Fujitsu Personal Systems, Inc. No part of this publication may be copied, reproduced, or translated, without the prior written consent of Fujitsu Personal Systems, Inc. No part of this publication may be stored or transmitted in any electronic form without the prior consent of Fujitsu Personal Systems, Inc. Agency Compliance UL Notices Cautions · For continued protection against the risk of fire, replace only with the same type and rating of fuse. [. . . ] If this is the case, pressing the Suspend/Resume button may not suspend system operation as described here. Contact your local help desk or reseller if your system configuration is not suitable. · The Suspend/Resume button on your system may be programmed to act as an On/Off switch. If this is the case, all active data will be lost if this button is pressed. In order to ensure that all active data is saved prior to turning off the system, exit Windows by choosing Shut Down from the Start menu and carry out the Shut Down command; this also turns off the system. · If your system is equipped with a PC Card that allows you to connect to a wired or wireless network, you may be logged off the network after a period of inactivity while system operation is suspended. Contact your network administrator or local help desk for details on log-off parameters for your network. Resuming System Operation To resume system operation, (from either Suspend-to-RAM or Suspend-to-Disk modes), press the Suspend/Resume button. 2 · From Suspend-to-RAM mode After a few seconds, the system returns to the Fully On state and system operation resumes. Note that the display turns on shortly before the pen becomes active due to the power-up sequences observed by the system. · From Suspend-to-Disk mode Active data is read from the hard disk drive, and after 15 to 30 seconds, the system returns to the Fully On state. 2-6 Using the Stylistic 2300 Pen Tablet Note that power to several system components must be restored before system operation resumes. Allow sufficient time for system operation to resume before attempting to use the system. If your system uses Suspend-to-Disk mode, it will take longer to resume operation as compared to using Suspend-to-RAM mode. (This action corresponds to a right-click operation with a mouse in most programs. ) · To move the cursor, hold the pen tip close to the display screen (within about 3/8 inch or 1 centimeter) and move the pen. · To start a program, double-tap the pen tip (tap the pen tip twice rapidly) on the program icon as you would double-click a mouse. · To drag an object, place the pen tip directly over the object, then press and hold the pen tip against the display screen while you move the pen. Pen Tether Attachment Point Pen Tip Thumb Grip Barrel Button Figure 2-2 Stylistic 2300 Pen Using the Pen 2-9 Charging the Battery Pack The Stylistic 2300 battery pack can be charged while it is installed in the pen tablet. Connect a DC power source, such as the AC adapter, to the DC input connector on the pen tablet. If the battery pack charge level is below 90%, the battery pack begins charging and the Charging icon appears in the Status display. If the battery pack charge is 90% or higher when you connect DC power, the battery pack will not charge; this prevents overcharging the battery pack. Look at the Battery Gauge icon in the Status display to determine the percent of charge in the battery pack. See "Status Display" in Chapter 1 of this manual for a description of the Battery Gauge icon. As long as DC power remains connected to the pen tablet, the charging process continues until the battery pack charge reaches 100%. Charge times shown in Table 2-2 are for a fully discharged battery pack charging both while the pen tablet is and is not in use. Table 2-2 Battery Pack Charging Time Battery Pack Charge Level Reached 90% 100% Approximate Charge Time (tablet not in use) 3 hours 5 hours Approximate Charge Time (tablet in use) 9 to 10 hours 12 hours Also note the following with respect to charging the battery pack: · You can use the system, suspend system operation, or shut down and turn off the system without interrupting the charging process; however, using the system while the battery pack is charging will cause the battery pack to charge at a slower rate, as noted in Table 2-2. · As noted in the procedure above, the system will not begin charging the battery pack if the battery pack charge level is 90% or higher when the system is initially connected to external DC power. [. . . ] This equipment may not be used on coin service telephones provided by your telephone company. Contact your state's public utility commission, public services commission, or corporation commission for more information. FCC rules prohibit the use of non-hearing aid compatible telephones in the following locations or applications: A-2 Appendix · All public or semipublic coin-operated or credit card telephones. · Elevators, highways, tunnels, (automobile, subway, railroad, or pedestrian) where a person with impaired hearing might be isolated in an emergency. [. . . ]